3mm vs 6mm ACM: Which Thickness Does Your Sign Need?
Most ACM sign jobs come down to one choice before you order: 3mm or 6mm. 3mm is the shop standard and covers most signs. 6mm costs more, but it holds a large panel flat where 3mm would flex. This guide explains what changes between the two thicknesses, which signs need 6mm, and what we stock in each.
The Short Answer
- 3mm for most sign work: post-mounted, wall-mounted, framed and real estate signs, directional signs and trade show panels.
- 6mm for site signs and other signs that take a higher wind load, plus large panels and longer unsupported spans.
The rule of thumb we give customers: if the sign is fixed to a building, 3mm is fine. If it is a site sign or will take a higher wind load, use 6mm.
What Changes Between 3mm and 6mm
ACM (aluminum composite material) is two thin aluminum faces bonded to a solid polyethylene core. On our sheets each face is 0.15mm aluminum in both thicknesses. Going from 3mm to 6mm adds core, which pushes the two faces further apart. That is what makes the 6mm panel much stiffer. The full specifications are on our ACM sign sheets page.
| Question | 3mm ACM | 6mm ACM |
|---|---|---|
| Stiffness | Rigid for most sign sizes | Much stiffer; resists flex over long spans |
| Weight | Lighter, easier to handle and hang | Heavier panel and heavier mounting |
| Cost | Lower | Higher |
| Edge | Thin, clean edge | Thicker edge that shows more from the side |
| Typical jobs | Post, wall, framed, real estate and directional signs | Site signs, big freestanding signs, long spans |
| Sheet sizes we stock | 4x8, 4x10, 5x10, plus 2x4 pre-cut pieces | 4x8 |
| Colors we stock | White/White, Black/Black, White/Primer | White/White |
When 3mm Is Enough
- Signs fixed to a building. The wall carries the panel, so 3mm is fine.
- Signs in a frame. A frame supports the edges. Our angle iron real estate frames are made for 3mm panels, and our pre-cut 2' x 4' pieces fit them. A 6mm panel is difficult to get behind their retainers.
- Post-mounted signs with supports close together. Parking, directional and business signs on posts are standard 3mm work.
- Anything handled or shipped often. Trade show panels and portable signs benefit from the lighter weight.
When to Step Up to 6mm
- Site signs and high wind loads. Freestanding site signs and signs in open, exposed spots take the most wind. That is where 6mm earns its cost.
- Large panels. The bigger the panel, the more 3mm can bow in the wind.
- Long unsupported spans. If the panel bridges a wide gap between posts or rails, 6mm stays flat where 3mm sags.
- Signs where flatness shows. Under raking light, a slight bow in a large panel is easy to see. 6mm holds a flatter face.
When it’s a close call, adding a support or frame to a 3mm panel can be cheaper than moving the whole sign to 6mm.
Mounting and Graphics
Graphics are the same on either thickness. Letter with Oracal 651 vinyl, or mount printed Orajet 3651 protected with an Oraguard overlaminate. For mounting, UHB tape works on both thicknesses. We also sell Excellart sign retainers for mounting sign panels; call us to order. Allow for the extra weight of 6mm panels when you choose fasteners and posts.
3mm and 6mm ACM Cut to Size
We cut ACM in-house. Our shear handles pieces up to about 50" wide, and larger cuts go on our panel saw. Send your sizes and quantities and we will cut full sheets down to your sign sizes. Full sheets ship by freight or are available for pickup in Omaha.
3mm vs 6mm ACM: FAQ
Is 3mm ACM strong enough for outdoor signs?
Yes. 3mm is the standard thickness for most outdoor sign work, including post-mounted, wall-mounted and framed signs. Choose 6mm for site signs and signs that take a higher wind load.
When should I use 6mm ACM?
Use 6mm for site signs and other signs that take a higher wind load, and for large panels with long unsupported spans. If the sign is fixed to a building, 3mm is fine.
Is 6mm ACM twice as heavy as 3mm?
It is heavier, but not double. The two 0.15mm aluminum faces are the same on both, and only the plastic core gets thicker.
What thickness is standard for ACM signs?
3mm. It is the most common ACM thickness for sign work, and 4' x 8' x 3mm White/White is our top-selling ACM sheet.
Do real estate frames take 3mm or 6mm ACM?
3mm. Our angle iron real estate frames are made for 3mm panels, including our pre-cut 2' x 4' ACM pieces. A 6mm panel is difficult to get behind the frame’s retainers.
What sizes and colors does 6mm ACM come in?
We stock 6mm ACM in 4' x 8' White/White only. 3mm comes in 4' x 8', 4' x 10' and 5' x 10', in White/White, Black/Black and White/Primer.
Can you cut 6mm ACM to size?
Yes. We cut ACM in-house on a shear for pieces up to about 50" wide and a panel saw for larger cuts. Contact us with your sizes.
Buy 3mm and 6mm ACM
Central Sign Supplies is a family-owned distributor in Omaha, Nebraska, supplying sign shops since 1951. No wholesale account is required. Shop ACM sign sheets or 2' x 4' pre-cut ACM pieces, pick up at 4222 D St in Omaha, or call 1-800-999-3160 for cut sizes and a freight quote.